A speed limiter is a device used to control the power of an electric golf cart. Some golf carts are equipped with EZ-Go speed chips that allow them to exceed their pre-programmed limits. This device is controlled by a small metal rod that is found next to the clutch and is connected to the cart’s engine through a cable. To remove the speed limiter, loosen the nut on this rod. While removing it, be aware that a quick adjustment to the speed can cause some problems.
Performance controllers can be as high as 650 amps
A good performance controller for an electric golf cart is a must. The controller needs to be able to handle high currents. If it doesn’t, the motor might overheat. The performance controller should be able to handle this, as well as other electrical issues. The controller is usually a three to four-hour job. It is also important to remember that a performance controller for a golf cart is different from one for a normal vehicle.
EZ-Go speed chip allows some golf carts to exceed pre-programmed speed limits
When you are on a golf course, you might be wondering how to remove the speed limiter on your electric golf cart. The speed limiter is a mechanical device that prevents the motor from exceeding the preset speed specifications. It is usually located next to the clutch. If you want to change the speed of your cart, you will have to unscrew the nut on this rod. However, you should be careful while removing the speed limiter, as you may cause damage to the cart or cause injuries.
If you want to change the speed limiter on your electric golf cart, there are two ways to do so. You can either upgrade the motor, or you can install a special electronic chip. Regardless of the method you choose, always remember to get help from an authorized reseller or professional. Performing DIY upgrades could void your golf cart’s warranty, so make sure you know what you are doing. Manufacturers of electric golf carts offer online resources where you can find dealers.
To remove the speed limiter, you will first need to locate the governor. This is the thickest cable that runs from the gas pedal and through the governor. You will need a screwdriver to reach this part. If you can see the governor, you can loosen the tension on the springs by rotating the nut in the direction of the notch on the shaft. The cable and spring are typically not visible, making the process more difficult. Unless you are experienced with electrical components and can find the right parts, you should consult a professional.
Removing the speed limiter on an electric golf cart is simple, but you should be careful not to overdo it. It will void the warranty and may cause serious damage to your cart. Depending on the model, you may be able to get ten miles per hour more from your cart. Depending on the model, this could be a great boost, but you should take the time to test the speed limiter before proceeding.
Adding a torque converter
You may have noticed that the speed limiter on your electric golf cart is preventing you from reaching the full potential of your cart. It can be frustrating to wait for the cart to rev up, and then find it is slowing you down. This is where a torque converter comes in. It is an electrical device that multiplies the motor’s torque by a gear ratio. For example, if the motor is only able to produce 5 ft-lbs of torque, the converter will multiply that into 15 ft-lbs of torque.
There are two main types of motor systems in an electric golf cart. There are series motors and shunt motors. Both systems require a specific voltage and amperage for maximum performance. Changing the components in the series system can give your cart a much higher top speed and torque. It can also increase your battery life. If you need to change your speed limiter, you may want to look at adding a torque converter.
When it comes to torque, you may also want to consider the DC series wound motors. These motors have larger field coils that generate a greater magnetic field. This means that the armature can spin faster, resulting in more top end speed. However, this sacrifice in top end speed is offset by the higher torque. You may want to consider this before making any changes.
Increasing the voltage of your golf cart’s batteries is another option for adding more power and speed. You should replace a 36-volt battery with 48-volt batteries. This is a simple and inexpensive upgrade, and requires no special skills. However, it may cost you more than $1,000 and requires labor. It is essential to keep your electric golf cart properly maintained so that it runs smoothly.
Another important factor in ensuring the longevity of your motor is its temperature. Plum Quick motors recommend that you monitor the temperature of your motor case regularly. Motors that are too hot can cause direct grounding and break winding shellac. To measure the temperature, you can buy a cheap Infrared Thermometer. If you don’t have one, you may want to consider purchasing one.
Upgrading your battery system
If you are looking for a simple solution to remove the speed limiter on your electric golf cart, consider upgrading your battery system. There are many advantages to this, including a lower price and the convenience of a local dealer. Battery installation is easier and safer with the help of a qualified professional. Dealers will ensure that your battery is charged and will perform a pre and post-installation safety check to ensure that your cart will run smoothly.
A 48V battery will allow you to remove the speed limiter on your electric golf cart. But be aware that you may have to compromise other aspects of the cart’s performance. A 48V battery, for example, can handle higher currents than a 24V battery. However, if you have a higher-end golf cart, you can upgrade the battery system to a 48V system.
A 48-volt system uses four batteries of different voltages, with the lowest voltage being 4-12 Volt. These are the cheapest, but they have the shortest range. Higher-quality batteries are heavier and have more lead. They also have higher range and last longer than lower-quality batteries. To upgrade your battery system, you can go through your golf cart’s owner’s manual to see the voltage of the battery.
If the voltage reading on the speed controller is three volts lower than the voltage of your battery, you’re likely to have a problem with the solenoid. If the solenoid is causing erratic driving, it might be a problem with the speed controller. Luckily, modern speed controllers are pretty reliable. However, the next time you want to remove speed limiter from your electric golf cart, you should make sure to upgrade the battery system first.
Your battery may be showing signs that it’s time to replace them. The best way to tell if your batteries need replacing is to perform a battery test. Most golf carts have a voltage meter on their dash. Analog meter is the most reliable, but electric gauges are less accurate. Also, remember to never let the fluid level fall below the battery plates, or you’ll risk damaging the battery.